Description: Wheel Hub Centric Spacer Adapters 15 mm 5x127 to 5x108 2 PCS At Caold Technology Pty Ltd, we are the most professional spacer manufacturing company. Many different types of style, every kind of specs available. There is noting we cannot produce. State of the art CNC machining, promising very precise results each and everytime. All spacers are made to order with very quick turnover time of 1 business day. Most importantly, all the machining are done locally in Melbourne, Australia. Thickness - 15 mm PCD - 5x127 (Car) to 5x108 (Wheel) CB - Custom machine, please provide required bore sizes of car and wheel Stud Size - M12x1.25 / M12x1.5 / M14x1.25 / M14x1.5 / 1/2"-20 UNF / 7/16" (Please specify size required) If you require a wheel centre bore >93.1mm, please contact us first as this may incur additional cost in order to produce Please note that we allow a tolerance of ±0.05-0.1mm on the centre bore sizing to allow for easier installation Qty: 2pcs Outer Diameter: 164mm Lip Height: 8mm Stud hole diameter: 15mm Bore depth varies according to thickness and difference between the wheel centre bore (WCB) and car centre bore (CCB) sizesSpacer Thickness Bore Depth A Bore Depth B15mm~12.5mm12mm20mm~18mm15mm25mm~22mm20mm30mm~27mm25mm35mm~32mm30mm40mm~37mm35mm50mm~47mm45mm Bore Depth A applies if: -2mm < WBB - CCB < 4mm Bore Depth B applies if: WBB - CCB < -2mm If WCB - CCB > 4mm the spacer bore is machined the entire way through without an internal supporting step required If you require clarification for any of the above information, please contact us! DISCLAIMERIn cases where the wheel centre bore is <4mm greater than the car centre bore, there is a step on the inside bore of the spacer in order to support the hub centric lip. So the spacer can sit flush on the hub, your vehicle's hub protrusion must not exceed the bore depth, so PLEASE CHECK YOUR HUB PROTRUSION BEFORE PURCHASING! Please see the picture below for how to measure and if you have questions or concerns please contact usIf you place an order and do not mention the hub protrusion to us, we will assume you have checked it and found it to be under the limit. If you do not check and find afterwards that your hub protrusion is too high for the spacers, the buyer will bear the cost of either fixing or replacing the spacers Before making your purchase, see this *Note- If your car uses lug bolts, you may need spacer bolts to screw these spacers onto your hub.*Sold separatelyAfter you placed the order sent us a message in this format(Year, Car Model)PCD (HUB)5x100 to PCD (Wheel) 5x100Car CB- (??.??)Wheel CB- (??.??)Lug Nuts- M12x1.25 or M12x1.5 or M14x1.25 or M14x1.5 or 1/2"-20 UNFFor Example:1910 Bravo Romeo 148PCD (HUB)5x98 to PCD (Wheel) 5x98Car CB- 58.1Wheel CB- 69.1Lug Bolts- M12x1.25If you are not sure what stud pattern profile is your car, contact us. We will try our best to assist you in finding the relevant information. Please let us know your car brand, model, year, we can provide you related data and information for you to refer to. Disclaimer Car Uses Studs Car Uses Bolts PCD Clearance Centerbore Clearance Prior to purchase of the spacer, you will need to read this information that may be is regarding to your vehicle. Any custom made purchases or orders will not be refundable as the spacer will only be made to suit YOUR car and YOUR wheel. Depending on the issue, we are open to negotiate and come up with a relatively reasonable solution. You will always have to confirm the spec with us, otherwise we cannot machine anything for you. Unless the description already have fixed detail on the spacer. If you are unsure of any of this information please let us know, we can go deeper into detail with you. If your car uses lug nuts (stud extrude from hub to tighten wheel down), you will need to know that if your studs is protruding out by 28mm and you are buying 15mm spacer, you will have 13mm extrusion from the surface of the spacer which might stop the wheels from sitting flat against the spacer refer to photo below. Thus if you get 30mm spacer, you definitely don't have to grind anything for sure. We will supply spacer nuts according to your car's stud, and insert studs according to your car's. If your car has M12x1.25 studs. We will provide M12x1.25 Spacer Nuts and M12x1.25 Studs into the spacer. This will allow you to use the factory lug nuts to tighten the wheel down. If your car uses lug bolts (threaded insert into the hub to tighten wheel down), that means you may need spacer bolts to secure the spacer onto your hub. The spacer bolts we have (sold separately) hex head is a little bit taller than the spacer for 15mm ref to photo below. It will be flush if the spacer is 20mm plus. ref to photo below. some cases where the wheels have gap in between the stud holes, hex head can perfectly sit in there, but only some cases works. For this set up if you want to use your factory lug bolts to tighten the spacer down, you might end up having the either grind the hex head down to stop any protrusion. ALSO the thread that surpass the hub might come to contact the hand brake mechanism or braking plate, this means the bolts is too long, you will have to grind the excess thread away to stop it from hitting the hand brake mechanism. If you are looking to change the PCD of the car to different PCD you will have to make sure the clearance at the back of the wheel allows you to commit this changes. Sometimes if there is a rebate or recess on the back of the wheel, does not mean there is enough clearance, usually if the stud pattern is changed dramatically (eg. 5x100 to 5x120) then there might be an issue. With Stock Bolt, in this wheel there is just enough rebate to allow the hex to sit in it, if there isn't a rebate you may need to get thicker spacer or grind down the hex head or get low profile hex bolt. Spacer shown is a 15mm spacer. For this specific rim there is a very deep rebate spacing, therefore will definitely have enough clearance for higher bolt. This rim has very shallow rebate (almost no rebate), the hex head will contact the wheel as the shown below, this will be very unsafe for you to use, as the wheel is not contacting the face of the spacer, only the hex head. Driving in this case may result in wheel breaking the stud off, with extreme vibration and tyre wear. Centerbore alignment is very important, and here is how we machine the size of our spacer. If you car has a Centerbore of 56.1mm, our adapter will be made 56.2mm roughly, with .1mm clearance will allow the spacer to fit on to your hub. When you do make a purchase and you want to have the clearance of the .1mm, just tell us the exact measurement. However if your wheel has a Centerbore of 56.1mm, we will make the hub centric lip to be 56.1mm or slightly smaller (less than .1mm difference). Simply because normally the wheel CB is slightly larger to allow the wheel to fit. If your Centerbore height is more than the spacer, it means you will either have to go with spacer without hub centric lip or us thicker spacer. As our hub centric spacer need to have taper to allow the change of center bore size. For Example if your Centerbore height is 12mm, you will have to go with 15mm spacer as minimum, if your Centerbore is 15mm tall, you will have to go with 20mm spacer. If your bore does not look anything similar to the photo shown below, send us a photo with as many dimensions included as you can, so we can try to determine how we can go about this. Material 6061 T6 Aluminium Alloy- T6 temper 6061 has an ultimate tensile strength of at least 290MPa (42,000 psi) and yield strength of at least 250 MPa (35,000 psi). More typical values are 310 MPa (45 ksi) and 270 MPa (39 ksi) respectively. Shipping Terms of sale Contact Us Return Policy - Parcels are shipped out generally within one business day after all information is collected. - Shipments will be handled by either Australian Post or Fastway Courier, we determine which to select based on your location with the most suitable shipping time. - If Australian Post Express option is not the default option, We have this option available with extra charges applied, contact us for more detail.- International Buyers (not in Australia), We ship worldwide, the charges are as listed it is standard post.Any import duty tax or charges we will not be responsible for this, you will also need to make sure your country allow such product to be imported. (If your product is held for custom clearance, they will not release the product until duty fee is cleared. This will delay the shipping time, please be aware and keep an eye on the tracking). -At Caold Technology our spacer adapters are made with state-of-the-art CNC machine in Melbourne, Australia, with the highest quality materials (Aluminum 6061-T6). All insert studs and nuts provided are Grade 10.9 steel. - All products & services we offer carry corresponding Australian laws & regulations. It is your responsibility, to make sure to use our product correctly. Wheel spacer are legally manufactured and intended for Exhibition Cars only. You are responsible to ensure the suitability and legality of items you intend to buy.We accept the return if The product was wrongly producedThe result of the spacer did not match your required specWe DO NOT accept returns if The item have been used, cause scratches in the product.You decided not to use it, or don't need it (change of mind)You used on non intended application and destroyed our productYou have damaged the product beyond repairSpecs provided was wrong One Year Manufacturing Guarantee At Caold technology, we produce reliable products, this is to give you a peace of mind when you use our product. We do not tolerate misuse, misconduct, abusive or improper installation.Guarantee does not apply to vehicle with aftermarket performance enhancement such as suspensions upgrades, any large gain of horse power to the wheels.Any defects to the product, buyer must take a picture immediately, and let us know. Return Policy (30 days) with 20% restocking fee applied. The product you purchased with information provided we will do it accordingly, if the fitment is wrong but we did however made it according to your measurements, It will be your expense. If you are unsure about this information, please contact us. We do machine spacers/adapters at varies thicknesses such as 15, 20, 25, 30, 35 mm or more. If you have any enquiry, complaints or feedback. Please email us. Contact us via Ebay. We will do our best to satisfy your needs and answers your question at our best ability. The product you purchased with information provided we will do it accordingly, if the fitment is wrong but we did however made it according to your measurements, It will be your expense. If you are unsure about this information, please contact us. All Our spacer adapters are made-to-order or custom made. Therefore we cannot accept any return.We accept the return if The product was wrongly producedThe result of the spacer did not match your required spec We DO NOT accept returns if The item have been used, cause scratches in the product.You decided not to use it, or don't need it (change of mind)You used on non intended application and destroyed our productYou have damaged the product beyond repairSpecs provided was wrong Any return items will be customer expense. One Year Manufacturing Guarantee, at Caold technology, we produce reliable products, this is to give you a peace of mind when you use our product. We do not tolerate misuse, misconduct, abusive or improper installation.Guarantee does not apply to vehicle with aftermarket performance enhancement such as suspensions upgrades, any large gain of horse power to the wheels. Any defects to the product, buyer must take a picture immediately, and let us know.
Price: 149.6 AUD
Location: Moorabbin
End Time: 2024-12-19T02:00:25.000Z
Shipping Cost: 52.24 AUD
Product Images
Item Specifics
Returns Accepted: ReturnsNotAccepted
Return policy details:
Brand: Caold Technology
Type: Spacer Adaptor
Classic Part: No
Number in Pack: 2
Manufacturer Part Number: CD1312132769
Features: Durable, Easy Installation
Placement on Vehicle: Front, Rear
Colour: Silver
