Voco Bifix SE Dual Curing Self adhesive Composite-based luting universal Shade

Description: DESCRIPTIONBifix SE:Dual-curing self-adhesive composite-based luting systemIndicationsDefinitive luting of inlays, onlays, crowns and bridges made from ceramic, zirconia, composite and/or metalDefinitive luting of metal, ceramic and fibre-reinforced postsNo etching, no bondingShort intraoral setting timeEasiest excess removalVery good adhesion to all materialsVery low water solubilityNo mixing mistakesExcellent biocompatibilityAvailable in three coloursWorking time: 90 s (23 °C)Intraoral working time after insertion: 30 - 60 sSetting time: 4 min (37 °C) Direction to UseRemoving the temporary and preparing the cavityRemove the temporary and thoroughly clean the cavity or prepared core, e.g. using oil- and fluoride-free cleaning paste.PreparationCheck the fit and contact points of the definitive restoration. If silicone has been used for verification, thoroughly remove silicone residues afterwards. Checking the occlusion on glass-ceramic restorations should only be carried out after definitive luting to reduce the risk of fracture. Remove any residue from the surface of the tooth and restoration after completing the try-in. Prepare the restoration according to the manufacturer’s instructions and dry it carefully. Dry the surface of the tooth, preferably with either a foam pellet or gentle puffs of air, leaving the dentine slightly moist.Inserting the restorationDue to technical reasons, there may be slight differences in the filling levels of the syringe chambers prior to first use. Therefore remove the syringe cap and extract material until both chambers deliver uniformly. Then fit a mixing tip type 14 or 15. The notches on the syringe and the mixing tip must line up exactly. Turn the mixing tip 90° clockwise to lock the tip into place. If necessary an intraoral tip type 1 can be attached to the end of the mixing tip type 15. To guarantee homogeneous mixing of both pastes, please discard the first 2 mm of the extracted material. After that, apply the material immediately and directly onto the prepared contact surfaces. Insert the restoration with the aim of leaving a small amount of excess material. Either replace transport cap or use the attached mixing tip as a cap.Removal of excess materialRemove excess material from difficult to reach areas first. Clean contact points and interproximal areas with dental floss. Excess cement can be removed with a suitable instrument (scaler) either during the gel phase (ca. 60 - 90 s after insertion) or after brief light-curing (1 - 2 s). Larger amounts of excess material are easier to remove. The restoration must be held in position during the polymerisation phase. As an alternative, any coarse pieces of excess luting composite can be removed with a foam pellet or a similar object immediately after insertion. Leave a small amount of excess material and cover it with a glycerine gel (air-block) or light-cure it.CuringPolymerisation time can be controlled with additional light-curing. Cure translucent restorations with light for 20 s on each side. Light-curing the luting gap for 10 s on each side is recommended for opaque restorations. The autopolymerisation of Bifix SE is completed 4 min after insertion.FinishingExcess material can be worked immediately after polymerisation. Remove cured excess material with a finishing diamond or flexible polishing disc. Finish approximal areas with finishing/polishing strips. 1 x QuickMix syringe 5g transparentAccessories Disclaimer "The sale of this item may be subject to regulation by the U.S. Food and Drug Administration and state and local regulatory agencies. If so, do not bid on this item unless you are an authorized purchaser. If the item is subject to FDA regulation, I will verify your status as an authorized purchaser of this item before shipping of the item." Business Information Name- PS ENTERPRISES City - Skokie State- Illinois Contact Number- +1 (904) 425-9702

Price: 57.84 USD

Location: Skokie, Illinois

End Time: 2024-11-03T12:14:07.000Z

Shipping Cost: 0 USD