SANSI 36W=350W 3600LM Motion Sensor LED Security Light Dusk to Dawn Floodlight

Description: Multiple Modes for Different Applications Compared with traditional motion sensor light for outdoor, it has more working modes. Not only owns Auto Mode but also includes Dusk to Dawn Mode and On-Time Mode. 4 different working modes will meet your needs. 1. Test Mode: The light turns on for only 5 seconds during daytime or night when in test mode. It helps you know whether the motion sensor is working well. 2. Auto Mode: When movement is detected in darkness, the light will turn on 1 to 10 minutes (depending on your setting on the “Time” knob); 3. On-Time Mode (controlled with on/off switch): The light turns on or off through the switch control. Light can work during daytime and night in on-time mode. 4. D2D (Dusk to Dawn) Mode: The light automatically turns on at dusk or night and stays off at daylight. Tips: The Lux knob is for brightness sensitivity, we recommend you set it in the halfway position. Dusk to Dawn MODE Put the "Mode" switch in the D2D position. Function: The light turns on automatically at dusk or night and turns off at dawn or if it’s too bright for your sensor. D2D Mode only works at night. When it's bright around the sensor, it goes off automatically. Except for Lux, Time and Range don't work while using this mode. TEST MODE Set-up: Put the "Mode" switch at the Test position. Function: The light turns on for only 5 seconds during daytime or night once it detects motion. This mode is used for checking whether the sensor is working properly. Test Mode can work during the daytime and night. Except for Range, the Lux and Time Setting doesn't work while using this mode. AUTO MODE Put the "Mode" switch at the Auto position. Function: When the sensor detects motion, it lights up for 1-10 minutes according to the time it has been set. While using the auto mode, the toggle switches off and 2 seconds later on again. The light turns on continuously for ca. 8 hrs and goes off in the daytime. Auto Mode only works at night. When it's bright (> 100-150 LUX) around the sensor, the light goes automatically back to Auto Mode. ON-TIME MODE Set-up: Put the "Mode" switch at the On-Time position. Function: Light can work as a standard LED light without motion sensing. The light turns on when switched on, turns off when switch off. On-Time Mode can work during the daytime and night. The Lux, Time, and Range Setting doesn't work while using this mode. Stand By Time Time knob is used for setting working time from 1-10 minutes when it detects motion. Time setting only works in Auto Mode. Sensor Sensitivity For setting ambient brightness value to differ from daytime tonight. If the ambient brightness value exceeds the setting Lux, it is defined as "daytime"; otherwise it's known as "nighttime". Position 0 equals 3 Lux, Position ∞ equals max Lux and it's always regarded as night no matter how bright around the sensor. Lux setting only works in Auto Mode and D2D Mode. Detecting Range Rotate the knob to adjust the sensing range to max ca. 50ft motion coverage. When you mount the light over 7.8ft, please adjust the sensor upwards and set the max range to increase the coverage area. Time setting only works in Auto Mode. Range setting only works in Test Mode and Auto Mode. Attention Make sure that there are no infrared or ambient lights pointing towards the motion sensor. Make sure that there are no other influence factors that affect the performance of light. Be sure to disconnect the power before you install the light. Be sure to mount it in a dry location, humid environment is not good for light's lifespan. Installation Tips: It is AC powered and required to be hardwired to the junction box. (NO Battery, No Solar) DO NOT install the camera on the opposite side of this security light because infrared rays will cause the security light to not work properly. If you still want it to be installed, please avoid infrared directly irradiated or reflection on the sensor. Recommend wall mounted, but also can be horizontally mounted under eave or soffit. Recommended installation height is 3.2~13.1 ft. If you mount this light over 8 ft, please adjust the angle of the sensor to enlarge the sensing range, otherwise, the performance of light will be affected. If you want to install two security lights in the same location, the distance between the two lights should be kept at least 16.4ft. Before installation, please read the user manual carefully and check if the light is in good condition or if some parts of the installation kit are missing. Please ask for help from us if you meet problems in installation. 4 in 1 Motion Sensor Outdoor LED Flood Light First: No reason to return within 30 days after receiving the goods Second (1) The seller pays the return shipping fee under the following circumstances: the fault party is the seller, and the shipping fee generated by the return is paid by the seller A. The buyer feels that the photos do not match the product description or that the product has certain defects. B. The received product does not work, the product is broken. C. The seller sent less spare parts when delivering the goods. D. The seller sent the wrong item when delivering the goods. E. After the buyer receives the goods, the goods are in a damaged state. (2) The return shipping fee is paid by the buyer in the following cases: The main reason for requesting a return is that the buyer himself does not want the item. For example: A. After receiving the goods, the buyer will feel that the product is not suitable and choose to return it. B. After buying the product, you don?t like it or don?t want it anymore, and you want to return it. C. After receiving the product, you found that other companies have a lower price, so I want to return it. D. It is purely because the buyer suddenly doesn't like the product and wants to return it. Our new products are generally guaranteed for five years, but the five-year warranty does not mean that any damage to the product within five years can be replaced unconditionally If your product is older than one year, you need to pay for shipping If your product is more than two years old, you need to pay part of the product price and freight according to the specific situation Second-hand product warranty period of three months

Price: 37.49 USD

Location: Union City, California

End Time: 2024-09-23T08:20:41.000Z

Shipping Cost: 0 USD