Phabrix Portable 3G/HD/SDI Video Analyzer

Description: Amazing little unit with multi-function capabilities including Waveform/Vector/Audio Analyzer plus Signal Generator with Networking for remote access. GENERATOR Video GeneratorCreate video test signals for all supported SD and HD SDI output standards including 1080p/50/59/60 Y, Cb, CrAdvanced video formats include support for RGB, XYZ 12bit and 2K formatsFully programmable Y Zone PlateAudio GeneratorEmbed audio signal on all 16 embedded audio outputsAudio Group menu controls which audio channels are present, signal type and amplitudeChoice of: silence, adjustable tone, noise, AV Delay, Dolby test stream or AES inputReferenceCreate video test signals that are either free-running or locked to studio reference or input signalGenlock menu is used to select locking reference and provides control for genlock phase offset in lines and pixelsANALYZERPicture MonitorPicture is displayed in window adown-converted displayCursor may be turned ON over area of picture specified by specific line and sampleMonitor device input or outputPicture ZoomZoom function provides 1:1 unfiltered pixel view, centred on position of picture cursorHANC/VANC areas visible when cursor in blankingLinked CursorsPicture cursor is linked to waveform, vectorscope and data views for rapid and accurate detailed measurement of signalWaveform Full FrameDisplays selected analyzer or generator sourceYCbCr GBR, Y, Cb, Cr, R, G, B modesCursors may be displayed over the waveform to allow measurement of time or amplitude valuesVertical and horizontal magnificationsWaveform Line SelectDisplay may be restricted to single line or all lines may be displayed simultaneouslySingle line display is linked to picture, vectorscope and data viewVectorscopeChoice of 100% or 75% graticulesDisplay Composite, SDI, SFP video input or generator test patternDisplay specific video line linked to picture cursor1, x2, x5 or x10 magnifications with position to centre, cyan, yellow, green, magenta, red, blue graticule locationsCONTROLScreen GrabScreen grabs can be saved and downloaded via web browser or FTP transferWeb BrowserView and control instrument display over TCP/IP interface with standard browserIdeal for remote location checking, engineering support, and fault analysisAllows access to key functions including screen dumps, loudness files and logging filesPC SimulatorFree simulator PC application is available for downloadIndicates command IDs for automation programmingAUDIO16 Channel Audio MetersDisplay up to 16 audio channelsSource for each block of 8 meters may be independently set to allow metering of embedded audio inputs or outputsCurrent audio level in dBFs (decibels relative to 0dB full-scale) is displayed at bottom of each meterAES/Analog Audio MetersDolby E metering selectionAudio Channel StatusAudio Status menu shows the Channel Status for selected audio channelDisplayed in decoded form as well as raw hexadecimal data dumpSource may either come from input signal or from generator output for rapid comparison purposesSYSTEMInstrument PresetsCurrent instrument settings can be saved as memories for future recallMemories can be exported to single files, reimported or copied to other unitsPresets can be applied to whole instrument or selectively within Generator or AnalyzerNetwork ConfigurationNetwork menu allows instrument to be configured as part of networkSupport for automatic acquisition of network parameters via DHCP or manual configurationRemote control enable/disable and selection of port numberSoftware StatusSerial number, instrument MAC address, version information and battery state listedDate and time can be set and factory default settings recalledDisplay of loaded license optionsLCD brightness and screen saver configurationsEngineer SetupManage instrument's settings including user access, clearing memories, factory default reset, software upgrades and audio calibrationSDI input to SDI output loop through modeUtilsDetails of the unit's operating statusDetails the temperature and individual board voltagesLists any hardware errors that have been recordedSIGNALVideo TimingDisplay relationship between selected video input with respect to external reference inputOffset feature to simplify system timing measurementsVideo StatusDisplay the status of the selected video input or output and any errors that have been found in data streamDisplay of EDH, Active Picture and CRC data with cumulative run-time display of errors and error rateDisplay of estimated cable length for SDI inputs with selectable cable typeANC StatusShows which ANC packets are present on SDI input and whether any errors have been detectedEach field is color coded according to whether ANC packet is present (White), missing (Grey), has errors (Red), or has previously had errors (yellow)Video Format/Payload IDMisc Status menu displays status of SMPTE 352 packets embedded in selected video input and displays any errors that have been foundSelection of input or output for rapid comparisonDisplay of raw data and decoded formLOGGINGLog SetupSet Audio Thresholds and log specific video status events, including Output, Reference and Input Status, TRS Errors, Picture CRCEvent Log DisplayEvent Log menu displays list of events with time stamp showing when they occurredANC Log SetupLog ANC Status menu allows customization of which ANC packets to log for changes in status (e.g. Present, Checksum Error, Missing, Parity Error)Logging of Dolby and AES Status as well as device system errorsControl of logging duration

Price: 3500 USD

Location: Washington, District Of Columbia

End Time: 2024-11-25T12:13:28.000Z

Shipping Cost: N/A USD