om606 HE221 (T25) Installation Kit for Holset Turbos

Description: om606 HE221 (T25) Installation Kit for Holset Turbos - Barb Fittings Mounting a Holset HE221 or other T25 frame turbo to your om606 can be a difficult task. Well no more! The BenzForce HE221 for om606 Kit takes the headache out of the physical connections. All that is needed is a 4AN feed line and a 3/4" drain hose. ** Turbo not included Here is what is included: BenzForce HE221 Wastegate Bracket Kit (with gasket and nuts). This bracket was engineered to have the proper wastegate preload. Instructions are below BenzForce 79mm exhaust v-band to 3" tube adapter for Holset turbos (adapter + clamp) BenzForce 3/4" Barb Oil Drain Tube for Holset T25 (screws, gasket, and drain) BenzForce HE221 (56mm) compressor v-band to coupler adapter (with clamp and o-ring) BenzForce om60x - 3/4" Barb to Block Turbo Drain Fitting (with gasket and bolts). BenzForce KKK to T25 Turbo Adapter kit (with studs, nuts, and gaskets) DCEC T25 manifold gaskets HE221 Turbine Flange Kit - 4 bolt (with bolts and gasket) Our BenzForce M10x1.25 to 4AN Turbo Feed Fitting - Restricted 1.68mm Wastegate Installation Instructions: Remove the wastegate hose Remove the wastegate actuator. After pulling the internal pin allowing the compressor housing to rotate independently, just remove to cotter pin on the wastegate (or a C-clip on the 5.5 cm2 models) and the two bolts holding the wastegate on the turbo. This will allow you to completely remove the wastegate. Mount the bracket. Remove the turbo from the T25 flange. Place, or replace, a new T25 gasket on the flange. Then install the wastegate bracket, followed by another T25 gasket. Install the turbo Reinstall the actuator. Rotate the actuator 180 degrees from its original position. Put the end over the pin on the turbine housing and install the original cotter pin or c-clip. Then pull the actuator and insert the original two bolts through the bracket and through the stock actuator bracket. The actuator comes pre-loaded from the factory so pulling the actuator should put the same amount of tension on the actuator as the original configuration. Use the included copper exhaust nuts to secure the actuator to the BenzForce bracket. Install boost hose. Depending on how the turbo is clocked, you can either reuse the existing boost hose or you may require a new one. Regardless, reinstall the hose so the actuator will see boost from the compressor housing. Note that the HE221 has clocking pins inside the turbo. Both the compressor and turbine housings pins will need to be removed in order to rotate the core om606 HE221 (T25) Installation Kit for Holset Turbos - Barb Fittings Mounting a Holset HE221 or other T25 frame turbo to your om606 can be a difficult task. Well no more! The BenzForce HE221 for om606 Kit takes the headache out of the physical connections. All that is needed is a 4AN feed line and a 3/4" drain hose. ** Turbo not included Here is what is included: BenzForce HE221 Wastegate Bracket Kit (with gasket and nuts). This bracket was engineered to have the proper wastegate preload. Instructions are below BenzForce 79mm exhaust v-band to 3" tube adapter for Holset turbos (adapter + clamp) BenzForce 3/4" Barb Oil Drain Tube for Holset T25 (screws, gasket, and drain) BenzForce HE221 (56mm) compressor v-band to coupler adapter (with clamp and o-ring) BenzForce om60x - 3/4" Barb to Block Turbo Drain Fitting (with gasket and bolts). BenzForce KKK to T25 Turbo Adapter kit (with studs, nuts, and gaskets) DCEC T25 manifold gaskets HE221 Turbine Flange Kit - 4 bolt (with bolts and gasket) Our BenzForce M10x1.25 to 4AN Turbo Feed Fitting - Restricted 1.68mm Wastegate Installation Instructions: Remove the wastegate hose Remove the wastegate actuator. After pulling the internal pin allowing the compressor housing to rotate independently, just remove to cotter pin on the wastegate (or a C-clip on the 5.5 cm2 models) and the two bolts holding the wastegate on the turbo. This will allow you to completely remove the wastegate. Mount the bracket. Remove the turbo from the T25 flange. Place, or replace, a new T25 gasket on the flange. Then install the wastegate bracket, followed by another T25 gasket. Install the turbo Reinstall the actuator. Rotate the actuator 180 degrees from its original position. Put the end over the pin on the turbine housing and install the original cotter pin or c-clip. Then pull the actuator and insert the original two bolts through the bracket and through the stock actuator bracket. The actuator comes pre-loaded from the factory so pulling the actuator should put the same amount of tension on the actuator as the original configuration. Use the included copper exhaust nuts to secure the actuator to the BenzForce bracket. Install boost hose. Depending on how the turbo is clocked, you can either reuse the existing boost hose or you may require a new one. Regardless, reinstall the hose so the actuator will see boost from the compressor housing. Note that the HE221 has clocking pins inside the turbo. Both the compressor and turbine housings pins will need to be removed in order to rotate the core × Buy now and save! Shipping info Click the Shipping & Payments tab above the listing description for more info Click the Shipping & Payments tab above the listing description for more info! Additional delivery notes PICK UP OPTION Sorry, our items are NOT available for pick-up. PAYMENT Immediate payment is required upon selecting "Buy It Now" or upon checking out through the cart. We accept payment via U.S. PayPal accounts and all Major Credit Cards, Debit Cards & Google Pay. We are legally required to collect sales tax in those states and localities where we maintain a physical presence (nexus). The applicable amount of sales tax charged to an order will be calculated based on the shipment destination's state and local sales tax laws. Thank you for shopping with us on eBay! Additional Information No additional information at this time Ask seller a question You might also like HX30 Super Oil Feed 4AN Restricted Intake manifold to 3" adapter for om648, om613 om606 X-Beam Connecting Rod om648 X-Beam Connecting Rod Contact To contact our Customer Service Team, simply click the button here and our Customer Service team will be happy to assist. Ask seller a question © BenzForce Shipping & Payments Click the Shipping & Payments tab above the listing description for more info Payment Accepted Payment Methods Immediate payment is required upon selecting "Buy It Now" or upon checking out through the cart. We accept payment via U.S. PayPal accounts and all Major Credit Cards, Debit Cards & Google Pay. We are legally required to collect sales tax in those states and localities where we maintain a physical presence (nexus). The applicable amount of sales tax charged to an order will be calculated based on the shipment destination's state and local sales tax laws. Thank you for shopping with us on eBay! Returns Returns are not accepted Seller will pay for return shipping. eBay integration by

Price: 299 USD

Location: Austin, Texas

End Time: 2024-01-25T03:47:25.000Z

Shipping Cost: N/A USD