Description: MAX TPC A/B THIXOTROPIC PATCHING COMPOUNDSYNTACTIC FOAM 96 OUNCE COMBINED VOLUME1/2 GALLON OF PART A-RESIN1 QUART OF PART B-CURING AGENT ØEasy 2:1 Parts By Weight or By VolumeØBrush, Spatula or Trowel AppliedØFor Fiberglass Patching, Honeycomb Bonding Edge Closeout, and FilletingØBonds To Epoxy, Polyester or Vinyl Ester Fiberglass HullsØBonds To Aluminum, Steel, Concrete, Wood, and CompositesØLightweight Density, Less Than 0.85G/CCØ15,000-PSI Compressive StrengthØWill Not Crack, Peel, or Chip Compared to Polyester (BONDO type) Body FillerØExcellent Water/Salt Water Resistant For Marine/Aero ApplicationsØSandable & Paintable Description MAX TPC A/B is specially formulated as a repair compound for filling holes, cracks, and divots caused by impact damage It is a “must have” repair compound for the marine and aircraft enthusiast. MAX TPC A/B is composed of glass microspheres or micro-balloons dispersed in a thixotropic epoxy-based resin system. This is known in the composites industry as a syntactic foam system. This resin system is also known as a syntactic foam in composites fabrication. It is used for honeycomb corefill, splicing and edge closeout MAX TPC A/B is a low density patching compound demonstrating high compressive strength, dimensional stability, and abrasion durability.It is suitable for continuous submerged applications and can withstand repeated temperature cycling(-10°C to 110°C) without cracking shrinking or delaminating from the applied substrate. MAX TPC A/B cures to a tough but easily sandable compound suitable for patching gauges, cracks, on composites wood or metal hulls or as an adhesive for lightweight applications. MAX TPC A/B can be used to fill in voids, divots or depression on concrete, Styrofoam, plastics and other substrates. It can also be used as a filler compound for cavities caused by wood rot damage.Other applications such as a low-density adhesive or filleting compound are also an excellent application for MAX TPC A/B. Usage And ApplicationDetermine the volume of resin and curing agent needed for the repair needed. If filling a cavity greater than 1 quart or 32 ounces of volume, prepare several batches of no more than 10 ounces per batch to avoid an exothermic heat build-up. Subsequent batches can be applied after allowing the previous batch to cure and cool the apply the next layer directly. Measure out two parts of PART A to one part PART B and gently mix for several minutes or until uniform in consistency. Transfer the mixed compound into another container and mix for another minute; this will ensure a thorough mixture. The mixed consistency is similar to mayonnaise. Clean and remove any loose material from the repair area and sand the surface to ensure the best adhesion. Use an acetone wipe to clean the area from any contaminants. Apply using a brush, spatula or inject into a cavity. It has a 30 minute working time and can be sanded after 24 hours of cure time. Handling strength will develop in 10 hours of room temperature curing and will fully cure within 24 to 36 hours. Exposing the gelled repair to mild heat (<200°F) will reduce cure time and can be sanded. Marine and Aircraft Composite Repair and FabricationElectronic Potting, Insulating, EncapsulatingHoneycomb Edge CloseoutFilleting CompoundLightweight AdhesiveGel Coat And Other Surface Repairs PHYSICAL PROPERTIESDensity0.85 G/CCForm and ColorNeutral White Paste (can be pigmented)ViscosityThixotropic – Mixed Viscosity 52,000 cpsMix Ratio(2:1)50 Parts “B” to 100 Parts “A” By Weight or VolumeWorking Time30 Minutes @ 25ºC (100 gram mass)Peak Exotherm57ºC (200-gram mass)Handle Time6 – 8 HoursCure Time24 to 36 Hrs. at 25°C or 4 hours Room Temperature Cure Minimum plus 25 Minutes @ 100ºC MECHANICAL PROPERTIESHardness82 ± 5 Shore DTee-Peel Strength5.6 Lbs. per inch WidthTensile Shear Strength2,300 psi @ 25ºC (77ºF) 1,100 psi @ 100ºC (212ºF) 2,823 psi @ -20ºC (-11ºF) Elongation to Break3.0% @ 25ºC (77ºF)Compressive Strength3,500 psiService Temperature-40 °C To 107ºC (225ºF) CUSTOMER TESTIMONIALGreetings, I have used the MAX TPC A/B on my Cadillac to fill in several trouble areas. One spot was rusted and close to unusable below the Cabriolet cover at the drip line on the rear quarter panel. The MAX TPC A/B did an outstanding job! I have spoken to several paint and body professionals and they agree that the MAX TPC A/B is a great product. They said it beats Bondo by a mile and will last a lifetime. I found the material mixed well and the hardener is great. The next morning I was able to sand and prime the car. Later I put on the Saxony Red paint and it turned out beautiful.Great product and keep up the good work. Jerry M. MAX TPC A/B MECHANICAL TEST AND APPLICATION DEMONSTRATION Wood Rot Damage Repair Structural Wood Columns Damaged Wood Wood Patch Remove Loose Wood Fibers For Best Adhesion MAX TPC Applied Using A Spatula Or Spreader Sanded Flush Ready For Painting Concrete Floor Patching Cracked Conrete Garage Floor Repaired MAX CFC Grey Concrete Floor Coating https://www.ebay.com/itm/222625093873 EPOXY RESIN MIXING AND USAGE APPLICATIONS The use of a weighing scale is highly recommended for proportioning the 2:1 mix ratio.Using volumetric measuring is fine, however, weighing the resin and curing agent yields better-cured mechanical properties, batch repeatability, and less waste from mixing over-sized batch.Use this digital scale to precisely weigh the resin and curing agent and ensure full polymerization of the resin and curing agent and prevent repair degradation. How To Mix Any Epoxy Resin And Avoid Cure Problems Click Window To Watch Video Demonstration SURFACE PREPARATION In virtually every application the surface to which the resin is applied MUST be well prepared to yield good adhesion. The following surface preparation procedures are recommended. METALSDegrease – Wipe laying surfaces with Methyl Ethyl Ketone (MEK) or acetone to remove all oil, dirt, and grease. Etch – For optimum results, metal parts should be immersed in a chromic acid bath solution consisting of:Sodium dichromate – 4 parts by weight Sulfuric acid – 10 parts by weightWater – 30 parts by weightThe solution should be held at a temperature of 160°F (71°C), and the parts left immersed for 5 to 7 minutes. Rinse – remove metal parts from etching bath and rinse in clean cold water (de-ionized water is recommended). If thoroughly clean, metal surfaces so treated will hold a thin film of water. Dry – To accelerate drying, items to be bonded can be placed in an air-circulating oven. ALTERNATE PROCEDUREDegrease, scour and dry – Often etching as outlined above is not practical. The surface must be cleaned by degreasing as noted above, scouring with an alkaline cleanser followed by rinsing and drying. Degrease and dry – Degrease the surface as noted above, sand or sandblast the surface lightly but thoroughly. Rinse with acetone or Methyl Ethyl Ketone (MEK), and dry.GLASSDegrease – With MEK as above, or with a strong boiling solution of a good grade household detergent. Etch – For optimum results, degreasing can be followed by the chromic acid bath outlined above. WOODSand – Bonding surfaces should be sanded lightly, but thoroughly to remove all external contamination. Clean – Carefully remove all dust, or particles of wood from sanded areas. A stiff and clean brush or compressed air can be used. PLASTICClean – Remove all dirt, oil, or other surfaces contaminated with detergent sop or degreasing solvent and water, followed by thorough rinsing and drying. A solvent that does not have a detrimental effect may also be used. Sand – Surfaces to be bonded should be sanded lightly, but thoroughly to remove surface sheen. Clean – Carefully remove all dust or particles of plastic from the sanded area. A clean brush, lint-free cloth, or compressed air may be used. DON'T FORGET OUR EPOXY MIXING KIT Click The Link To Add To Order https://www.ebay.com/itm/222623932456 EVERYTHING YOU NEED TO MEASURE, MIX, DISPENSE OR APPLY Proportioning the correct amount is equally as important to attain the intended cured properties of the resin system. The container in which the epoxy and curing agent is mixed is an important consideration when mixing an epoxy resin system. The container must withstand the tenacity of the chemical and must be free of contamination. Most epoxy curing agent has a degree of corrosivity, as a general practice, protective gloves should be worn when handling chemicals of the same nature. MIXING KIT CONTENTS 1 Each Digital Scale -Durable, Accurate Up To 2000.0 Grams 4 Each 32-ounce (1 Quart) Clear HDPE Plastic Mix Cups4 Each 16-ounce (1 Pint) Clear HDPE Plastic Mix CupsOne Size Fits All Powder-Free Latex Gloves 2 Each Graduated SyringesWooden Stir SticksAssorted Size Foam Brush THANKS FOR STOPPING BY IMPORTANT NOTICE Your purchase constitutes the acceptance of this disclaimer. Please review before purchasing this product.The user should thoroughly test any proposed use of this product and independently conclude satisfactory performance in the application. Likewise, if the manner in which this product is used requires government approval or clearance, the user must obtain said approval. The information contained herein is based on data believed to be accurate at the time of publication. Data and parameters cited have been obtained through published information, PolymerProducts and Polymer Composites Inc. laboratories using materials under controlled conditions. Data of this type should not be used for a specification for fabrication and design. It is the user's responsibility to determine this Composites fitness for use.There is no warranty of merchantability of fitness for use, nor any other express implied warranty. The user's exclusive remedy and the manufacturer's liability are limited to the refund of the purchase price or replacement of the product within the agreed warranty period. PolymerProducts and its direct representative will not be liable for incidental or consequential damages of any kind. Determination of the suitability of any kind of information or product for the use contemplated by the user, the manner of that use and whether there is any infringement of patents is the sole liability of the user.
Price: 59.49 USD
Location: Ontario, California
End Time: 2025-01-27T02:03:37.000Z
Shipping Cost: 0.72 USD
Product Images
Item Specifics
Restocking Fee: No
Return shipping will be paid by: Buyer
All returns accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money Back
Model: MAX TPC A/B
Modified Item: No
Country/Region of Manufacture: United States
California Prop 65 Warning: PROP 65 WARNING: This product contains less than 0.1% of a chemical known to the State of California to cause cancer ●EPA SARA Title III Section 313 above ‘de minimus’ level: None ●All components of this product are on the TSCA Inventory or are exempt per 40 CFR 720.30 IMPORTANT USAGE INFORMATION POSTED ON THE DESCRIPTION PAGE
PATCHING COMPOUND: FOR FIBERGLASS, WOOD, METALS, CONCRETE
AUTOMOTIVE CAR BODY FILLER RUST REPAIR: BONDS TO METALS, WOOD, PLASTICS, CONCRETE
EXCELLENT SANDABILITY AFTER 24 CURE: PAINT BONDS DIRECTLY TO SURFACE
Type: Crack And Void Repair Epoxy Compound
Expiration Date: Does Not Expire
MPN: MAXTPC96OZ
Brand: MAX TPC A/B
