Cheek Rest For Crosman 1399, Benjamin Marauder Shoulder Stock

Description: For sale is a custom designed Cheek Rest Mount with an optional Genuine MAGPUL CTR/MOE 0.25" Cheek Riser. This is designed to fit the rifle stock that is included with the Benjamin Marauder PCP Air Pistol. This may also fit other Crosman air guns that accept the Crosman 1399 Custom Shoulder Stock such as the following air guns: PC77, 1377, 1322, 2240, 2300, 1740, 2400, etc. All metric hardware is included, which is stainless steel with stainless nylock nuts; hex-wrench included. No extra tools or disassembly required. The Cheek Rest Mount alone weighs 3.6 oz/102 g with hardware. The Magpul 1/4" cheek rest riser weighs 1.8 oz/54 g. Combined the weight is 5.4 oz/156 g. The Cheek Rest Mount is adjustable front-to-back and in height. This requires the installation of a MAGPUL CTR/MOE Cheek Riser (or compatible) to complete the "Cheek Rest". I recommend the 1/4" riser from MAGPUL due to the mount having height adjustability (I use the lowest position with a 1/4" MAGPUL cheek riser with medium height scope rings). You can purchase just the Cheek Rest Mount and use your own MAGPUL CTR riser, or purchase both here. The Cheek Rest Mount is 3D printed in the USA, using Carbon Fiber infused extreme black PETG (premium milled carbon fiber, NOT powder or dust) which is also made in the USA. This plastic will not warp when exposed to outdoor heat, or left in the sun. The Mount has a deep black slightly textured surface. Installation:1 - Install the two posts into the main large Cheek Rest mount, which has the Top and Front labeled, using the two (2) long screws and two (2) nylock nuts (do not fully tighten yet). Make sure the nylock nuts seat correctly into the hex-shaped recess.I recommend installing the the posts with the "angled" side toward the barrel (flat side toward the rear of the stock). 2 - Install the assembled Cheek Rest Mount onto the Crosman shoulder stock using the remaining eight (8) short screws and eight (8) nylock nuts (do not fully tighten yet).Make sure the nylock nuts seat correctly into the hex-shaped recess. 3 - Install the MAGPUL Cheek Riser of your choice. 4 - Set the assembly front-to-back to your liking, then tighten the eight (8) screws holding the assembly onto the stock.Note: The front post needs to be at least 1 1/8" back from its most forward possible mounting position (the stock is too narrow in that area to get a tight fit). 5 - Set the height to match your scope or other optic using the different height holes on the 3D printed posts (removing the two (2) long screws might be needed to do this).Note: With the 1/4" riser, I use the bottom-most hole on the front post and the second-from-bottom hole on the rear post to get the correct height and level for my scope. 6 - Once you have everything lined up and where you want it, snug all the screws using the provided hex-wrench. DO NOT OVERTIGHTEN, the screws need to be just snug enough so there is no play. DONE - Enjoy your new Cheek Rest. Exclusively designed and 3D printed in the USAMade with Carbon Fiber infused Extra-Tough polymer plasticSimple yet solid long lasting designThese are designed and 3D printed in the USA, by Crooks USA - You wont find these anywhere else. The rifle, scope, stand, and all other parts & accessories are NOT included. MADE IN THE USA THESE ARE PARTS ONLY. THEY ARE NOT FOR ILLEGAL USE.THESE DO NOT ADD TO OR ALTER ANY FIREARM IN ANY WAY. PLEASE FOLLOW ALL FEDERAL, STATE & LOCAL LAWS.

Price: 25 USD

Location: Rosemead, California

End Time: 2024-11-04T00:35:41.000Z

Shipping Cost: N/A USD